There are many methods to save the power like Switching the street light on detecting vehicle , Street light controlling using LDR and relays etc. The proposed circuits controls street light intensity by calculating the peak hours.Two circuits are shown in this article,one explaining the street light control using ATmega8 and second explains street light controlling using PIC microcontroller. Most commonly found street lights are HID or High Intensity Discharge lamps, which consume a lot of power. In order to save energy, the circuits are designed with high intensity LEDs in place of HID lamps.
Auto Intensity Control of Street Lights using ATmega8
Circuit Principle
The main principle of this project is to Control the intensity of street lights using PWM.Peak hours of a particular area are calculated and accordingly PWM signal is adjusted by microcontroller to increase or decrease the intensity of street lights. These peak hours can be calculated by considering parameters like traffic density,time, light intensity of the environment.
Auto Intensity Control of Street Lights Circuit Diagram
Circuit Components
ATmega8 micro controller DS1307 IC Light Dependent Resistor LED array. LCD display
DS1307 DataSheet LCD DataSheet
Circuit Design
The auto intensity control of street lights circuit is simple but it requires more coding part. This circuit consists of Atmega8 controller, DS1307, LDR, Relay and LEDs. LDR:LDR is used for calculating the light intensity of the environment .The light dependent resistor is connected to ADC1 (PC1) pin of the micro controller. The analog light value is converted to digital value using ADC. RTC:Current time is calculated using RTC. Real time clock has 8 pins out of which SCL and SDA are connected to PC5 andPC4 pins respectively. SCL is serial clock while SDA is serial data RTC is I2C compatible, where I2C means inter integrated circuit. One bit of data is transmitted on data bus for each clock cycle. Data can be transferred between devices, using only two bi-directional buses. Each device can act as a slave or master. The slave devices will have one address and these devices can be accessed using this address. LCD:LCD is the display used for displaying time which is read from RTC IC. Interfacing of LCD in 4-bit mode is shown in circuit diagram. D4-D7 pins of LCD are connected to PD0-PD3 pins of microcontroller. RS pin of LCD is connected to PD4 pin of micro controller. RW and Enable pins are connected to PD5 and PD6 pins of controller. LED array is number of high power LEDs connected in series. It is connected to PWM pin of the microcontroller.
I2C Protocol
I2c is a communication protocol invented by Philips Company. This is well suited for communication between integrated circuits and peripherals. This uses two lines to transfer data.
Serial Data – SDA Serial Clock – SCL.
Simulation Video
How Auto Intensity Control of Street Lights Circuit Works?
Code is written in such a way that up to 2 am lights will glow with full intensity. From then it slowly starts decreasing and finally it drops to zero in the morning.
Limitations of this Circuit
Even though energy is saved if there are any vehicles after fixed time, intensity of the light is low. Maximum energy cannot be saved.
Auto Intensity Control of Street Lights using a PIC Microcontroller
Circuit Diagram
Components
IC1 PIC 16F877A IC2 DS 1307 LCD1 16X2 Alphanumeric LCD display R1, R2 10 KΩ R3, R4 1 KΩ R5 10 KΩ R6 1 KΩ R7 10 KΩ R8, R9, R10 and R11 330 Ω R12 10 KΩ R13 10 KΩ POT
Component Description
PIC16F877A The microcontroller used in the circuit is a PIC16F877A. It is an 8 – bit microcontroller that reads the voltage across LDR and also checks the time in Real Time Clock IC. Based on the readings, the LEDs are switched on or off. DS1307 It is a Real Time Clock IC. The communication between microcontroller and DS1307 is via I2C protocol. It provides clock and calendar with details like seconds, minutes, hours, day, date, month and year. Time can be set in either 12 hour mode or 24 hour mode and there is an indication of AM/PM.
Working
We use both LDR and RTC in the circuit for the following reason: if only LDR is used, then there is no chance of saving any energy as the street lights will glow as soon as the intensity of light on LDR decreases and when the intensity increases, the street lights are turned off. If only RTC is used, the street lights are turned on and off at preset time irrespective of the outside lighting conditions. When the device is turned on, RTC starts with the preset time in the code. The microcontroller waits for the signal from LDR and when the intensity of light on LDR decreases, the output of the microcontroller is activated and the street lights start to glow. This event occurs only when the current time is in the range of preset time i.e. only after 5PM. The lights continue to glow at full intensity up to 3 AM. When the time reaches 3 AM, the intensity of the street light gradually decreases and will turn off either at 6 AM or when the light on LDR in increasing, whichever is first. Hence, the auto intensity control of street lights is achieved with the above circuit which has an LDR, an RTC, a PIC microcontroller and an LED array.
Alternative Circuit
The circuits shown above uses array of LEDs as street light in order to save power. But the same circuit can also be used to fire a normal HID street lamp. The circuit for auto intensity control of HID street light is as follows.
The above circuit shows only the interface to the street light and the rest of the circuit is same. It consists of a relay, a high intensity discharge street light that is connected to the mains supply and a diode. The relay contact is made only when the intensity of light on the LDR is low and the street light glows.
Auto Intensity Control of Street Lights Circuit Advantages
Power wastage can be reduced. Using LED array reduces the cost. Using of RTC and LDR produces accurate results.
Comment * Name * Email * Website
Δ
